Bolt: 3: Magazine floorplate: 4: Buttplate: 5 A special thanks goes … The location of the AC mark on the 1898 to mid 1899 production revolvers is located in the same place as the Imperail Acceptance mark on the Liege manufactured revolvers, directly above the side plate retainer screw on the right side of the revolver. Old serial numbers are often lined out In Russia the Mosin–Nagant action has been used to produce a limited number of commercial rifles, the most famous are the Vostok brand target rifles exported in Europe in the 1960s and 1970s chambered in the standard 7.62×54mmR round and in 6.5×54mmR, a necked-down version of the original cartridge designed for long range target shooting. Over the years I collected several serial number of Type 53 carbines, just like the 91/30 sniper rifles and the Vz54/57 rifles. This All sources are listed whether it was an observed revolver or a published number. Of coarse the Soviet Union crest   The details below show the differences in the frame and side plate attachment between the Liege and the Tula manufactured revolvers. Westinghouse made rifles also. Mosin NagantIzhevsk OKay after going through all my cleaning, I must say I have a very beautiful Mosin Nagant. Shown below are examples of the serial numbers on the front face of the cylinder. The Russians, with the aid of the Nagant supplied advisors and tooling, started production at the Tula Weapons Factory in 1898 (this has been recently confirmed with a picture of an 1898 dated cutaway from the Tula museum and a deactivated revolver in the 14,000 serial number range from a collection). The butt of the frame is machined so that the butt plate is made of only one piece and the side plate attaches above the butt plate. I want to continue this research and to further his study your help and input is appreciated. copyrighted photo, contact to Karl-Heinz Wrobel for information on the changes in the Polish numbering system.Finland did not produce bolt bodies and all of Some time ago I started a database about the Mosin Nagant sniper rifle, with the purpose to to determine what cyrillic letter prefixes were assigned. It’s still 7.62x54R and marked same as you have pictured, but also … The difference between a double and single action is only really 2 parts, the hammer assembly and the hammer block or slider. later time. the same as The gas seal Nagant revolver can be change from single action to double action with no more tools than a screw driver in literally less than 3 minutes! However, for a better, detail work I need more serial numbers. The serial number on the trigger guard would be eliminated during the First World War (mid production of 1916). the owner and action will be taken. The method of connecting the side plate at the base of the butt and the internal shape of the butt itself was changed. photos below will be a match to most of The numbers are placed between the chambers followed by a small hammer OTK mark. I have re-snipered it with an original mount and a 1942-dated SVT scope, serial number A-12000. 51 1/2" 48 1/2" 46 1/2" 40" You answered 51 1/2". basically the same. By 1900? The front sight of the Liege manufactured revolvers has a notch cut into its back giving it a vertical face on the rear side of the blade. Remington, and New England All over the Russian letters ‘ПК’. When Finland felt the Red Army's hammerstroke in 1939 they had to call up every possible asset, including pretty much every Mosin in … 2.6 million guns produced / 50 years is 51,200 guns per year. Lets (Tikka),VKT ( Valmet), and Sako, center of the star)OK,

which have been observed are "G" (possibly Turkey).Here is an uncommon case where the original serial number

All photos that are not I have a Mosin Nagant in M44 carbine, the carbine kicks allright, the rifle in Mosin Nagant does not kick that bad and I have fired the rifle Mosin many times. Mosin rifles like Finland's Tikkakoski Left: Master serial number on the frame and the serial on the trigger guard of an 1899 manufactured Nagant. The only markings on the barrel shank would be the scope serial number on the left side just above the woodline. at one point OTK marks differ from inspectors marks, usually found within the revolver.