All BrandsWorked for Kawasaki Motors as a Product Support Specialist (Factory Support) for 24 yearsI operate a motorcycle dealership and CCS Ducati Race team.6 years Motorcycle/ATV/Water Craft; 4 years auto; 18 years carpenterDisclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts.
Where is the neutral safety switch on a 05 rhino? Feels as though the slips then reconnects witha snap.
rarely does the neutral light come one. The Neutral light and Low light won't come on and I was told that its because the Neutral switch assy was bad! By continuing to use this site you consent to the use of cookies on your device as described in our By continuing to use this site you consent to the use of cookies on your device as described in our I have a 2006 Yamaha Rhino 660. 3G1-82540-01-00, 3G1-82540-02-00 . recommend you and use you in the future.9 dollars, 2 hours of my time, and I drove away. Another great insight to what may be the problem. I had real doubts about this website but your promptness of response, quick followup and to the point answer with picture was incredible.As a single woman, I really appreciate an excellent and affordable opinion. I get to testing...Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. It is held in by two 10mm bolts and will be hard to get out and probably break around outside.
The neutral switch is also under the airbox, but bolts in to the side of the cases on the drivers side. Does this sound right? The transmission seems to be functioning properly in that the vehicle operates normally with the exception of the indicator lights.
Ill chech it out,, again,, thanks.Well,,, Im sure not getting much help on this here!The neutral switch, if I am not mistaken, is located on the back side of the shifter. But they can give me a price on one though!under air box, just forward of the oil filter housing, gear position switch. I am looking for any solution possible!i changed the clutch in my 2003 raptor 660. now it is having a tough time shifting, if it does at all. 1995 Yamaha Wolverine … Mechanic's Assistant: Just to … I filled tank up and it would still not start, I replaced fuel filter then Rhino 660 clicks at the starter but doesn't turn over the motor. I have not had any trouble with my brake lights, but you may be able to clean the switch with a good contact cleaner and check the switch with an ohm meter afterward. See all vehicles this product fits. Lurch. I had trouble with a switch on mine, but I don't remember if it was the reverse switch or the neutral. Is the wiring comingMy Rhino 660 has a transmission problem.
not the single wire one, that is for rev.their is two bolts on it. It almost seems like a position sensor or something, as it seems to have a tiny area that it will come on, but you have to very carefully move the shifter around a little till it comes on, but it seems in colder weather it is much harder to find the spot.. if that makes sense.. but its getting aggravating,, if Im out riding and shut it off, it may take me 15 minutes to get it started again! replaced an A/C fan motor. I DROVE IT YESTERDAY AND PUT IT ON THE TRAILER.
The new switch cost me 145nzd from yamaha. It is part #2 in the diagramJeff Policky and 87 other Motorcycle Specialists are ready to help youThanks for the info. I cannot thank you enough for your help. Lurch. I found mine just hanging by the wire. you can lightly sand the contacts then put some dielectric grease on them.
Is there someone that can help me out? I have only used it sparingly since this problem started a couple weeks ago.OK. The shift position indicators sometimes all come on, or sometimes one or two. Can you tell me what number item the switch is in the diagram you sent so I know it when I see it. sounds like the clutch pulley or something iI have a 2006 Yamaha Rhino 660. JavaScript is disabled. FYI, engine was rebuilt du2nd gear is slipping but all others are fine. Want Answer 0. Thank you so much.
Any ideas what the problem maybe and how to correct it? Clicking this will make more experts see the question and we will remind you when it gets answered.
2006 Yamaha Rhino 450 4x4 Rhino 450 4x4, ROOF AND WINDSHIELD, CALL SALES @ 920-788-0220!Every Bit As Rugged As Its Big Brother This one has all the big Rhino features in a valu... Ken's Sports Kaukauna, WI Remove both seats, remove engine cover, remover airbox (two plastic plugs at front of airbox, hose clamp holding airbox to throttle body, there is two hoses on air box that just pull off). When you say the switch is on the left side of the motor I assume it is the drivers side and is it accessed by removing the seats and center console or by lifting the bed?Yes the drivers side is the left side.
Today, June 20, it was doing the samhave a 94 yamaha rhino 660, dealer rebuilt engine and it has lost a valve twice since. By chatting and providing personal info, you understand and agree to our I have a Yamaha rhino 660, 2006 model. The brake lights at the rear of the Rhino should come on. Yamaha Gold, Suzuki Gold, Honda Bronze, Polaris Bronze, BRPHonda registered technician, silver level award, former Kawasaki/Suzuki tech, 40+ years exp.Over 25 years experience, ICS, MMI, Owned shop for 12 years, worked tech-support for Harley DavidsonMotorcycle, ATV, Mules, Side by Side's Product Specialist.