Then I got an error code that said PC - 1392511 If the meter measures infinite resistance, check resistance directly at the ice maker fill tube heater. The meter should measure about 120 ohms through the defrost heater. Reconnect the wires if loose. The meter should measure near 0 ohms of resistance through the defrost bi-metal thermostat. Find and repair the sensor wiring failure if the meter measures infinite resistance through the sensor wires.Unplug the refrigerator and check the humidity sensor wire harness connection. Reconnect the wires if loose.
If sensor resistance is okay, reinstall the ice room temperature sensor and check the sensor's wire harness connections to the electronic control board (orange wire on CN78 and gray wires on CN76). The meter should measure about 135 ohms through the air damper heater. If the wire connections are okay, disconnect the sensor wires from the electronic control board and measure resistance through the sensor's wires.
Sign in with Facebook If the defrost heater and bi-metal thermostat are both okay, find and repair the wiring break in the defrost circuit that is preventing the heater from getting electrical current.Check freezer temperature because the ice maker won't cycle if freezer temperature is above 15 degrees.
FRENCH DOOR REFRIGERATOR. You go to grab something from the refrigerator and notice that there is an error code flashing. If the meter measures around 50 ohms through the gray and brown wires, then you'll likely need to replace the electronic control board because it isn't accurately detecting humidity sensor resistance. Reconnect the wires if loose. You can redisplay a detected error code by pressing and holding the Energy Saver and Lighting buttons simultaneously for 8 seconds. View and Download Samsung RF28HMEDBSR service manual online.
Welcome to Master Electronics Repair!
The meter should measure about 120 ohms of resistance.
Using a multimeter, check resistance through the air damper heater (connected to the black and brown wires). RF28HMEDBSR refrigerator pdf manual download. Our app is now available on Google Play
If the wiring connections are okay, replace the refrigerator evaporator fan.Unplug the refrigerator and check the wire harness connections on the condenser fan. The control may continue to display the code even if the component failure no longer exists.
The Samsung secret codes are used by developers and designers to access hidden settings and features. Power on, have reset on the display and cut power for 2 minutes to … If sensor resistance is okay, reinstall the temperature sensor and check the sensor's wire harness connections to the electronic control board (yellow wire on CN30 and gray wire on CN76). Find and repair the sensor wiring failure if the meter measures infinite resistance through the sensor wires.Refrigerator compartment temperature sensor failureUnplug the refrigerator and check the wire harness connection on the refrigerator compartment temperature sensor. If humidity sensor resistance through the yellow and gray wires is around 50 ohms, plug the humidity sensor back into the wire harness and check resistance through the gray and brown humidity sensor wires that connect to CN30 on the electronic control board. Replace the temperature sensor if resistance is off by more than 10 percent.
The meter should read the same resistance as for the temperature sensor. Reconnect the wires if loose. Reconnect any loose wires.
Reconnect any loose wires. The technician will need to conduct live voltage checks to determine the cause of the problem.Call a service technician to diagnose and repair this failure. The air damper heater is included with the pantry drawer air damper motor and isn't available as a separate component.
Reconnect any loose wires.
Replace the temperature sensor if resistance is off by more than 10 percent.
Reconnect the wire harness if it's loose. If the wire connections are okay, disconnect the sensor wires from the electronic control board and measure resistance through the sensor's wires. website.Here you will find:Service Modes, Circuit Diagrams,Service manuals, Firmware Update procedure, Disassemble procedure, Universal remote control setup codes, Troubleshooting, Diagnosing, Measuring, and more.... of many of LCD/LED TV/Displays,others various electronic apparates,trough many technical notes and tips/tricks to help … If the humidity sensor wire harness connection is okay, unplug the humidity sensor and check resistance through the yellow and gray humidity sensor wires using a multimeter. My Samsung refrigerator is off, a PC Ch code is on the display. If the meter measures infinite resistance through the air damper heater wires, find and repair the wiring break in the damper heater wires.Unplug the refrigerator and remove the electronic control board cover. If the problem continues, replace the control panel.Unplug the refrigerator and check the wire harness connections between the inverter board and compressor. The meter should measure about 5,600 ohms if the sensor temperature is 72 degrees (room temperature), 13,290 ohms at 32 degrees and 29,000 at 0 degrees. The meter should measure about 5,600 ohms if the sensor temperature is 72 degrees (room temperature). If wiring connections are okay, call a service technician to diagnose and repair the compressor failure. I had a power surge. If wiring connections are sound, you'll likely need to replace the electronic control board.